{"product_id":"spw-replacement-wrclik-tr-transmitter-for-hunter-wrclik-wrfclik-grey-white-transmitter-only-easy-pairing","title":"SPW replacement WRCLIK-TR transmitter for Hunter WRCLIK\/WRFCLIK - grey\/white transmitter-only, easy pairing","description":"\u003cp\u003e\u003cstrong\u003eThis is the SPW replacement WRCLIK-TR transmitter for Hunter WRCLIK and WRFCLIK rain\/freeze sensor systems — transmitter only, requires pairing with your existing receiver.\u003c\/strong\u003e\u003c\/p\u003e\n\n\u003cp\u003eIf your rain or rain-and-freeze sensor stopped communicating, you don’t always need a full kit replacement. This product is a transmitter-only unit intended to substitute the original WRCLIK transmitter and restore wireless signaling to a compatible Hunter receiver. It arrives unpaired and must be addressed (paired) to your existing receiver before it will operate; follow the manufacturer addressing steps and allow the sensor’s internal hydrostatic disks to dry before testing.\u003c\/p\u003e\n\n\u003ch3\u003eHow do I get this replacement transmitter working with my receiver?\u003c\/h3\u003e\n\n\u003cp\u003ePairing (or addressing) is required to link this transmitter to your receiver. The sensor must be dry and the test spindle able to be pressed so the red LED will flash during the addressing process. If the LED does not light, place the sensor in sunlight with the vent fully open until the internal components dry.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eConfirm your receiver is compatible with WRCLIK\/WRFCLIK transmitters (not compatible with dangling-wire antenna receiver types).\u003c\/li\u003e\n  \u003cli\u003eAllow the sensor’s hydrostatic disks to dry fully before testing or addressing.\u003c\/li\u003e\n  \u003cli\u003ePress the test spindle; the red LED should flash to indicate readiness to pair.\u003c\/li\u003e\n  \u003cli\u003eSearch “WRCLIK Addressing” online for step-by-step illustrated instructions.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat troubleshooting steps help if the transmitter LED won’t light?\u003c\/h3\u003e\n\n\u003cp\u003eOften the LED stays off because the sensor was factory-tested and remained moist in transit. Drying the unit and exposing it to sun with the vent open usually restores normal function. If the LED still does not flash after drying, reach out for support rather than returning immediately.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eOpen the vent fully and set the sensor in direct sunlight to speed drying.\u003c\/li\u003e\n  \u003cli\u003eWait until the hydrostatic disks are dry and the test spindle moves freely.\u003c\/li\u003e\n  \u003cli\u003eIf problems persist, contact the seller for guided troubleshooting before initiating a return.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWill this transmitter work with my current Hunter rain or freeze receiver?\u003c\/h3\u003e\n\n\u003cp\u003eThis unit is designed to work with WRCLIK (rain only) and WRFCLIK (rain + freeze) receiver systems, replacing the transmitter side only. It is not compatible with older or different Hunter receivers that use an exposed dangling-wire antenna; those setups require purchasing a full replacement kit.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eCompatible: receivers designed for WRCLIK or WRFCLIK protocols.\u003c\/li\u003e\n  \u003cli\u003eNot compatible: receivers using dangling-wire antenna designs — full kit recommended.\u003c\/li\u003e\n  \u003cli\u003eVerify compatibility before purchase to avoid unnecessary returns.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat should I expect after installation and pairing?\u003c\/h3\u003e\n\n\u003cp\u003eOnce properly addressed to your receiver, the replacement transmitter will resume signaling rain and\/or freeze conditions to your irrigation controller, allowing the controller to suspend scheduled watering as intended. Regularly inspect the sensor and vents for debris and ensure it can dry after rain events to maintain accurate performance.\u003c\/p\u003e\n\n\u003cul\u003e\n  \u003cli\u003eAfter successful pairing, test the transmitter by activating the test spindle and observing receiver response.\u003c\/li\u003e\n  \u003cli\u003eKeep vents clear so the sensor can dry and reset between wet events.\u003c\/li\u003e\n  \u003cli\u003eContact support if signal range or responsiveness seems reduced.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWho is this for: This replacement transmitter is for homeowners, landscapers, and irrigation techs who already own a compatible Hunter WRCLIK or WRFCLIK receiver and need to replace a failed transmitter without buying a complete new sensor kit. Choose this unit if you can verify receiver compatibility and are comfortable following addressing steps or seeking quick help from the seller when needed.\u003c\/p\u003e\n\u003csection class=\"product-faq-snippet\"\u003e\u003ch3\u003eFAQ\u003c\/h3\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Is this transmitter compatible with my Hunter WRCLIK receiver?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: Yes — compatible with WRCLIK and WRFCLIK receivers. It won’t work with receivers that use a dangling-wire antenna; those need a full kit.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv class=\"faq-item\"\u003e\n\u003cp class=\"faq-q\"\u003eQ: Why won’t the transmitter’s red LED turn on?\u003c\/p\u003e\n\u003cp class=\"faq-a\"\u003eA: The unit may be damp from factory testing. Open the vent and dry in sunlight until the hydrostatic disks are dry and the test spindle triggers the LED.\u003c\/p\u003e\n\u003c\/div\u003e\u003c\/section\u003e","brand":"SPW","offers":[{"title":"Default Title","offer_id":56843599249748,"sku":"B0D72C9JWX","price":112.82,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1063\/2652\/4244\/files\/spw-wrcliktr-transmitter-front.jpg?v=1787080976","url":"https:\/\/gardenluxe.co.uk\/products\/spw-replacement-wrclik-tr-transmitter-for-hunter-wrclik-wrfclik-grey-white-transmitter-only-easy-pairing","provider":"Gardenluxe Uk","version":"1.0","type":"link"}